See full list on linkedin25CR - Chemical Composition - Continental AlloysAvailable in bar dimensions of 50.8 mm (2") to 431.8 mm (17") Length range up to 9.14 m (30') From materials management to threading, cutting, machining and heat-treating, Continental is a one-stop provider of the steel products and services the oil and gas industry needs.
30CrNiMo8 / 1.6580 - SteelNumber - Chemical composition Alloy special steel Chemical composition of steel 30CrNiMo8 (1.6580), Standards of steel 30CrNiMo8 (1.6580) Mechanical Properties of steel 30CrNiMo8 (1.6580) Equivalent grades of steel 30CrNiMo8 (1.6580) steel 30CrNiMo8 (1.6580) Tensile Strength, Elongation, Proof strength , Hardness
Alloy special steel Chemical composition of steel 41Cr4 (1.7035), Standards of steel 41Cr4 (1.7035) Mechanical Properties of steel 41Cr4 (1.7035) Equivalent grades of steel 41Cr4 (1.7035) steel 41Cr4 (1.7035) Tensile Strength, Elongation, Proof strength , Hardness
42CrMo Steel Equivalent, Chemical Composition, Mechanical
IntroductionApplicationsDatasheetEquivalentSearch for specific steel grades in production range of Chemical composition and mechanical properties of steel grades acc. to EN, ASTM, ASME, API, GOST, JIS. UNI, NF A, BS standards. Call now +421 903 246073.
Carbon Equivalent - Leong HuatBase composition:0.25% C, 0.30% Si, 0.70% Mn . The ability to form hard metallurgical constituents such as martensites or any other hard phases is dependent on the carbon equivalent and the cooling rate of the steel involved in cooling from the transformation temperature.
The "L" stands for "low carbon" content. Due to lower carbon amount AISI 316L (1.4404) stainless steel has reduced risk of sensitization (grain boundary carbide precipitation) but at the same time, it loses some of its strength. AISI 316LN (1.4406) stainless steel is alloyed with nitrogen to compensate for the loss of strength. Chemical Composition
G-NiCr28W / 2.4879 - SteelNumber - Chemical composition Chemical composition of steel G-NiCr28W (2.4879), Standards of steel G-NiCr28W (2.4879) Mechanical Properties of steel G-NiCr28W (2.4879) steel G-NiCr28W (2.4879) Tensile Strength, Elongation, Proof strength , Hardness
L80 - Chemical Composition - Continental AlloysManufactured to API specification 5CT. This is a controlled yield strength material with a hardness testing requirement. L80 is usually used in wells with sour (hydrogen sulfide) environments. Available in casing dimensions of 114.3 mm (4.5") to 406.4 mm (16") Available
When stainless steel is analyzed with XPS or Auger, four steps are included:Step 1. Stainless steel XPS survey spectrum. A survey scan determines the overall elemental composition of the surface from atomic numbers 3-92. This determines the composition of the passive layer elemental composition and surface Cr/Fe ratio.
What is 9Cr18MoV Steel? [Complete Steel Guide] - Knife UserAccording to the chemical composition and the HRC of the steel, the 9cr18MoV Steel has the following features:9cr18MoV Edge Retention:9cr18MoV has a high level of Chromium and Carbon (close to 1% of carbon) and maximum hardness of 60HRC, which makes it hard with a great Edge Retention. 9cr18MoV Corrosion Resistance:With 18% of Chromium 9cr18MoV offers great corrosion resistance.
X12Cr13, 1.4006, AISI 410 - stainless steelX12Cr13, 1.4006, AISI 410 - stainless steel X12Cr13, 1.4006, AISI 410 - Construction martensitic stainless chromium steel suitable for parts and components of devices working in the area of steam and water, according to EN 10088-1.
Chemical Composition of Structural Steels carbon is by far the most important chemical element in steel. Increasing the carbon content produces a material with higher strength and lower ductility. Structural steels, therefore, have carbon contents between 0.15 to 0.30 percent; if the carbon Chromium (Cr) Chromium is present in certain